您好： 我用的是新華龍的F340的單片機，數據線接的P3口，片選信號線接P0.6,A0接P0.7,那么在程序起先CH375HM_INDEX和CH375HM_DATA分別應該定義多少呢，還有想弱弱的問一下，想暫時調試看結果的話除了這個改動外，別的相對于例子程序外沒有什么改的吧

1.模塊上的RD,WR,A0,CS,數據線要是直接掛在單片機總線上,根據A0,CS計算下總線地址.A0=0索引端口,A0=1數據端口.要不是掛在總線上,就不用計算這個地址,直接用模擬I/O口進行讀寫操做, 2.只要根據你的單片機改下硬件定義,中斷腳和三個讀寫子函數就可以了.

請問“直接用模擬I/O口進行讀寫操做”，不明白啊

就是根據時序要求,直接對這些I/O口進行操作,例如: void CH375HM_INDEX_WR ( unsigned char Index) { CH375HM_D0_D7 = Index; CH375HM_A0 = 0; CH375HM_DATA_DIR_OUT( ); /* 設置并口方向?yàn)檩敵?*/ CH375HM_RD = 1; 如果I/O默認電平是高電平,那么這是可選操作 CH375HM_CS = 0; CH375HM_WR = 0;

CH375HM_CS =0; //對于高速單片機,該指令用于延時,以便向CH375_WR產生寬度至少為80nS的低電平脈沖

CH375HM_WR = 1; CH375HM_CS = 1; CH375HM_A0 = 1; CH375HM_DATA_DIR_IN( ); /* 禁止數據輸出 */

}

void CH375HM_DATA_WR (unsigned char dat ) { CH375HM_D0_D7 = dat; CH375HM_DATA_DIR_OUT( ); CH375HM_A0 = 1; CH375HM_CS = 0; CH375HM_WR = 0;

CH375HM_CS = 0; // 對于高速單片機,該指令用于延時,以便向CH375_WR產生寬度至少為80nS的低電平脈沖

CH375HM_WR = 1; CH375HM_CS = 1; CH375HM_DATA_DIR_IN( ); /* 禁止數據輸出 */ }

unsigned char CH375HM_DATA_RD( void ) {

unsigned char dat; CH375HM_DATA_DIR_IN(); CH375HM_A0 = 1; CH375HM_CS = 0; CH375HM_RD = 0;

CH375HM_CS=0; //對于高速單片機，該指令用于延時，以便向CH375_RD產生寬度至少為80nS的低電平脈沖

dat = CH375HM_D0_D7 CH375HM_CS = 1; CH375HM_A0 = 0; return( dat );

}